FIX: Lenovo Laptop HAS POWER but NO DISPLAY/ BLACK SCREEN (after switching EUFI to LEGACY on BIOS)

PROBLEM:
Lenovo S145 Laptop. HAS POWER but NO DISPLAY/ BLACK SCREEN (after switching EUFI to LEGACY on BIOS)

Troubleshooting (did not wok with my laptop problem)

- Power off, then reset RAM

- Remove the battery, then long press the power button for 30 seconds, then retart. then power on without battery

- Reset the CMOS battery connection

- Remove the battery, cmos, ram, harddrive connections (for about an hour), then long press the power button for 30 seconds, connect all parts, then power on

SOLUTION: Re-access BIOS setup then switch back to EUFI

Follow these steps accordingly

press novo button (wait for about 10-15 seconds before accessing the BIOS setup)
press DOWN ARROW KEY "once"
press ENTER KEY "once"
press RIGHT ARROW KEY "3 times"
press ENTER KEY "once"
press UP ARROW KEY "once"
press ENTER KEY "once"
press RIGHT ARROW KEY "once"
press ENTER KEY "2 times"

DONE!!!

Comments

How to reset Ink Levels in Epson L110 (or L Series)

UPDATE: Another Solution Solution A: 1. Unhook the ink tank unit and lay it down, just like when you're refilling inks. 2. Wait for about 10-15 seconds, then hook it back 3. Press the "red ink light" button 4. Done Note: sometimes, you have to set first the transportation lock to the locked position before doing the steps Solution B: 1. Power off the Printer. 2. Put a bondpaper on the loading tray. 3. Press both Power Button and paper feed or ink button for 15 seconds. 4. After 15 seconds, release power button and paper feed or ink button. Paper feed or ink button with orange light will steady while the power button will be blinking. 5. Now press once the paper feed or ink button (with orange light). Wait until a test print is done, it takes about 30-60 seconds (or longer) 6. After a test print, the blinking of ink button will stop and printer is ready to use

FIXED: How to solve 192.168.1.1 ERROR CODE SSL ERROR UNSUPPORTED VERSION on Firefox

😫I can't find the solution on the internet so I decided to...🤔 Let's solve this problem in less than 1 Minute! 192.168.1.1 ERROR CODE: SSL_ERROR_UNSUPPORTED_VERSION Please "like," "share," and "subscribe" to our channel " youtube.com/digitalphpro" so that we can help others too. Thank you Problem: Secure Connection Failed. ERROR CODE: SSL_ERROR_UNSUPPORTED_VERSION An error occurred during a connection to 192.168.1.1. Peer using an unsupported version of security protocol. This Website might not support the TLS 1.2 protocol, which is the minimum version supported by firefox Solution: Change TLS minimum version to 1 1. Type in “about:config” into the firefox browser address bar 2. You will reach the “Proceed with Caution”page click on “Accept Risk and Continue” 3. On the net page in the “search preference name” section type in “security.tls.version.min” 4. Click on the pencil icon right next to the search result and change the no i...

Connected to the internet but can't browse a site while other computers and mobile can browse

PROBLEM : Connected to the internet but can't browse a site while other computers and mobile can browse. Waiting for proxy tunnel Ping was okay, getting replies from " www.google.com -t " . It means that my i have internet connection Solutions that i've tried: Solution 1: Check your computer's time if correct. Solution 2: Use other internet browser (Firefox or Opera) Solution 3. Run Windows Network Diagnostic Solution 4: Restart your computer Solution 5 : Clear browsing history then Restart Solution 6 . Restart the modem & router Solution 7 . Renewing my IP Address by using the " ipconfig /release" then " ipconfig /renew". Restart Solution 8 . Scan for viruses then Restart SOLUTION : (This solution fixed my internet browsing problem) 6. Uncheck the "Authomatically detect settings" box 9. Click the Refresh icon or RELOAD buttonn

Computer Problems and Solutions

Search This Blog